SAUNAS, STEAM ROOMS AND COLD PLUNGES

Sauna and Steam Room Construction in Miami

Rendering of a thermal circuit corridor with a glowing sauna, marble steam room, and tiled cold plunge under a pendant light in a New York wellness club by Aquatics International Group
Concept rendering of a sauna and steam room suite in a Miami residence by Aquatics International Group

One Team From Room Prep To First Heat

Most sauna and steam companies in South Florida sell you a cabin and set it in a room somebody else built. The waterproofing, the vapor barrier, the ventilation, the drainage, the electrical service and the building approvals are left to you or your contractor.

Aquatics International Group builds the room. We handle the substrate and waterproofing, the vapor control that keeps humidity out of the surrounding structure, the ventilation and drainage, the power to the heater or generator, and the coordination with your architect, engineer and building management. Whether the sauna is site built in cedar or a manufactured cabin dropped into a space we prepared, one team is responsible from the first demo to the first heat.

That is the same scope we carried building the aquatic wellness facilities at TMPL in New York City.

 

Built to Pass Inspection and Last for Decades

Humidity Is the Whole Problem

A steam room pushes vapor into every wall it touches. In South Florida the air outside the room is already carrying moisture, so a vapor barrier that would pass in a dry climate fails here. We detail the barrier, the drainage, and dedicated exhaust that runs to the outside, and we coordinate structural loads with the engineer of record before a location is chosen, not after.


Built for Salt Air and Florida Code

Oceanfront work means salt gets into everything. We specify marine grade hardware, stainless with the right alloy for the exposure, and finishes that survive a building three blocks from the water. Permits, Florida Building Code compliance, and condo or hotel management approvals are handled before demolition starts.


Self-Performed,
Single Contract

We prepare the room, run the power and ventilation, and install the sauna, steam room, and cold plunge, supplying equipment through our dealer lines. You get a facility with mechanical you can actually service. One contract, one warranty, one number to call.

Luxury thermal suite with sunken cold plunge pool, glass-enclosed sauna and steam room, and warm backlit wood paneling

Cold Plunges and Contrast Therapy

Cold plunges built in concrete, preformed EPS, or stainless steel, with dedicated chillers, set indoors or on terraces and paired with your sauna and steam room as one contrast therapy circuit. Vessel material, chilling capacity, and sanitation are covered in detail on our cold plunge and contrast therapy page.

Every plunge gets its own filtration, sanitation, and chiller, sized for how many people actually use it. We plan the electrical, drainage, and equipment access with the rest of the room during design, so the plunge is part of the build rather than an add on.

Saunas, Steam Rooms, and Hammams

Heat rooms are where most wellness buildouts go wrong, because the problem isn’t the cabin, it’s what the cabin does to the building around it. We install every heat room with the vapor barriers, sloped ceilings, and dedicated exhaust that keep moisture out of adjacent walls, size heaters and generators to the electrical service that actually exists, and coordinate the exhaust with the base building mechanical system so the spa never fights the HVAC.

We supply traditional saunas, infrared rooms, steam generators, and hammam heating through our dealer lines and build the rooms around them. Cost ranges and lead times are covered in the FAQ below.

Finished custom cedar sauna interior with tiered benches and continuous LED strip lighting under each bench and at the ceiling line
Concept rendering of a rooftop cold plunge and sauna terrace overlooking the ocean at a Miami Beach residence by Aquatics International Group

Rooftop and Terrace Wellness

Outdoor plunges and sauna cabins on rooftops, terraces, and pool decks, including preformed EPS and stainless steel vessels light enough for elevated slabs. We coordinate structural loads with the engineer of record, place mechanical where it can be serviced without a crane, and detail wind loads, salt air protection, and drainage so the installation holds up to an oceanfront exposure and a hurricane season.

The cold side of the contrast cycle comes with it: experience showers, ice fountains, and snow rooms for cooling between rounds without a full immersion plunge.

Every Feature in the Circuit

Certified and Factory Backed

Why a Contractor and Not a Dealer

Most companies selling saunas and steam rooms in South Florida are dealers. They sell you a cabin, set it in the space, connect what is already there, and leave. If the room behind it was not built for heat and vapor, that becomes your problem in about eighteen months, and it shows up as a stain on the neighbor’s wall or a warped door that will not seal.

Aquatics International Group is a construction company. We demolish, frame, waterproof, run the electrical service, build the ventilation, tile the steam room, set the plunge, and install the sauna. Where a manufactured cabin is the right answer, we supply it through our dealer lines and build the room it goes into. Where site built is the right answer, we build it.

That is the same scope we carried on the aquatic wellness facilities at TMPL in New York City, at every location.

Three sauna heaters and cedar benching under installation with a Himalayan salt wall at TMPL NYC, built by Aquatics International Group

Built for the Operators Who Cannot Close

Aquatics International Group built the aquatic wellness facilities at TMPL in New York City, at every location: saunas, steam rooms, cold plunges, and the mechanical behind them, installed in occupied high rise buildings on a schedule that could not slip.

That is the standard we bring to a Miami condominium tower, a hotel spa, or an oceanfront estate.

Where We Build in South Florida

Miami Beach, Bal Harbour, Sunny Isles Beach, Coral Gables, Key Biscayne, Aventura, Fort Lauderdale, Boca Raton, and Palm Beach. We work on oceanfront residences, condominium amenity floors, hotels, and private clubs across Miami-Dade, Broward, and Palm Beach counties.

Aquatics International Group is based in South Florida with offices in New York City and the Caribbean. If your project sits outside these areas, call and we will tell you honestly whether we are the right contractor for it.

 

Frequently Asked Questions

What does a custom sauna or steam room cost in Miami?

Most residential sauna and steam room projects fall in a range we can give you on a first call once we know the size of the room, whether it is new construction or a retrofit, and what has to happen behind the walls. Commercial and amenity floor work is quoted from drawings. We do not quote from a photo.

How long does a sauna or steam room take to build?

Plan on design and permitting first, then construction. Retrofits into an existing room move faster than new construction. Lead time on a manufactured cabin runs separately from the build, so we order early and sequence the room around it.

Can you build in a condominium building?

Yes, and most of our South Florida work is in one. Condominium and hotel projects mean association approval, insurance requirements, elevator and loading dock scheduling, and work hour restrictions. We handle that coordination as part of the job rather than handing you a list of things to go solve.

Do you build the room or just install the equipment?

Both. We prepare and build the room, waterproofing, vapor barrier, ventilation, electrical and drainage, then install the sauna, steam room, and cold plunge. That is what separates a construction contractor from a dealer.

Can you add a cold plunge to a sauna or steam room project?

Yes. We build cold plunges alongside saunas and steam rooms as one contrast therapy suite, in concrete, preformed EPS, or stainless steel, with dedicated chilling, filtration, and drainage planned during design so everything fits the space and the building’s requirements.

How do you handle Florida humidity and salt air?

Every detail on an oceanfront project is chosen for the exposure: the vapor barrier, the hardware alloy, the ventilation path, and the finish on anything metal. A specification that works inland will fail three blocks from the water, and we build for where the project actually is.

Let’s Start Your Project

Type
Project Types Filters
Project Locations Filters
Skip to content